Commercial Panic Bar / Exit Device Installation

Why this matters

Exit devices (panic bars) are required on egress doors in most commercial / institutional buildings. The IBC and NFPA 101 specify when they're needed and the operational requirements. Customers needing exit device installation, replacement, or service represent a substantial segment of commercial locksmith work. Proper installation is essential for fire safety and code compliance.

When exit devices are required

Per IBC + NFPA 101:

The customer's specific occupancy classification determines requirements.

Exit device types

Selection depends on the door type + code requirements + aesthetic.

Major brands

Each manufacturer offers specific models for each application.

Code requirements

Panic hardware must:

• Open in the direction of egress
• Allow exit with no more than 15 lb of force
• Operate via single-point activation (push bar)
• Not require any other action (key, code, etc.) for egress
• Remain operable under all conditions

These requirements are non-negotiable. Code compliance during installation is the locksmith's responsibility.

Pre-installation survey

Before installation:

1. Identify door type (wood, metal, glass)
2. Identify door size + thickness
3. Identify door frame type (wood, metal, knock-down, welded)
4. Identify the existing hardware (what's being replaced)
5. Verify egress requirement (which direction must the door swing)
6. Identify any electrification (electric strike, magnetic lock paired)
7. Verify ADA compliance (lever vs. paddle for accessibility)
8. Confirm fire rating of the door (if applicable; specific exit hardware for fire-rated doors)

This information drives the hardware selection.

Selecting the exit device

For each opening:

1. Door swing direction: in or out
2. Single or pair of doors: pair needs additional considerations
3. Indoor or outdoor: outdoor needs weatherproofing
4. Indoor traffic level: higher traffic = heavier-duty hardware
5. Lockable from outside (with key) or always exit-only
6. Special features: alarm, signaling, audit trail

Installation procedure

Step 1: Remove existing hardware

1. Remove the existing knob, lock, hinges (if needed)
2. Remove the existing strike plate
3. Save hardware in case the customer wants to retain

Step 2: Verify door preparation

The door needs:

• Cylinder hole at the correct height
• Latch bolt opening
• Mounting holes per the exit device's template
• Cuts at the correct depth

If preparation is missing, additional work needed.

Step 3: Install the exit device

1. Mount the device per manufacturer template
2. Secure to the door
3. Adjust for proper operation
4. Verify the latch engages properly

Step 4: Install the strike

1. Position the strike on the door frame
2. Secure with proper fasteners
3. Verify alignment with the latch
4. Test door operation

Step 5: Verify operation

1. Operate the device several times
2. Verify the latch retracts on push
3. Verify the latch engages when door closes
4. Verify 15 lb force compliance (manufacturer typically tests; verify in field)
5. Test from both sides of the door

Step 6: Adjust as needed

Common adjustments:

• Latch height
• Strike position
• Closer adjustment (if door has a closer)
• Hinge alignment

Pairs of doors

For pairs:

1. Active leaf: typically has the exit device + standard latch
2. Inactive leaf: has flush bolts or coordinator
3. Mullion: removable center post that aligns the doors
4. Coordination: ensures the inactive leaf closes first

Pairs add complexity. Both leaves need to satisfy egress requirements.

Fire-rated doors

Fire-rated doors require:

• Fire-rated exit devices (specific listing)
• Fire-rated strike plates
• Fire-rated hinges
• No modifications to the door (other than approved)
• Annual inspection (NFPA 80 requirement for fire doors)

The customer's fire-rated door designation must be matched with fire-rated hardware.

Electrification

Many exit devices are electrified:

Coordinate with access control system if integration is needed.

Common adjustments

After installation:

Maintenance

For installed exit devices:

Annual service contracts are typical for commercial exit devices.

Customer education

For exit device customers:

1. "Your exit door is the means of egress; it must remain operational"
2. "Don't block the exit; the bar must be pushable from inside at any time"
3. "Annual inspection is required for code compliance"
4. "Don't lock the door from outside without verifying egress from inside still works"

Common pitfalls

References

• IBC (International Building Code) Chapter 10 (Means of Egress)
• NFPA 101 (Life Safety Code)
• NFPA 80 (Fire Door Inspection)
• ADA Standards
• BHMA / ANSI A156.3 (Exit Devices)
• UL 305 (Panic Hardware)
• Manufacturer documentation (Von Duprin, Sargent, Schlage)
• Manuall internal: Lock Types Mechanisms, Electronic Access Control, Master Key Systems